Some time ago I use the new digital consoles BlackMagic, and truth are great (no one pays for this, is only the fruit of my experience) but when using it for professionals who are accustomed to analog consoles or analog part, can be a big shock. If we also add that the support is in English frustration with a problem can be uppercase.
I have prepared some important considerations when installing that I hope will be helpful. I will of course in Spanish 
. Questions, suggestions or comments do not hesitate to get them myself.
Connecting a control panel
If you have purchased a panel Broadcaster ATEM, then you will have to wait to connect your computer. (It allows you to connect directly without having to set. Is all set to work plug and play).
Step 1. Connect power to the panel Broadcaster ATEM.
Step 2. Connect one end of an Ethernet cable to an Ethernet port on the control panel. Either
ports will operate, since it is an Ethernet switch within the panel, so both ports operate exactly like.
Step 3. Connect the other end of the cable to the Ethernet port on the chassis of ATEM processor
label switching control.
If everything is working well, should see the lights flashing on the Ethernet port, and the panel should be illuminated buttons, and the main display panel should read ATEM production switcher.
If required (without no problems do not do it) manually configure network settings, then you may need help from a technician
IP addresses. By default, processor chassis ATEM provides a fixed IP address 192.168.10.240, transmission is set a fixed IP 192.168.10.10, therefore should be connected directly without any problem
The connection to your computer
You can connect your computer directly into the ATEM switch so you can control the switch, upload files, pool of graphics and clips, and change the mixer settings.
Connecting your computer is easy and after installing the software simply follow the ATEM Switcher instructions below:
Step 1. Connect an Ethernet cable from the Ethernet port chassis control switch to the Ethernet port of your computer.
If you have a panel of installed hardware, and has the wing attached ATEM, then, Connect the equipment to the second Ethernet port on the panel. Now the
panel can be operated in parallel.
Step 2. Make sure your switch is on ATEM.
Step 3. In the network settings on your computer, enter the IP address 192.168.10.50.
Now when you run the ATEM Control Software should see the tab buttons on the control of light and display the status switch.
His ATEM switch defaults to a fixed IP. IP Address 192.168.10.240 when sending and, dela using ATEM configuration Utilidadde, You can customize the network configuration.
Changing the switching network
The network settings are changed switcher mediantela ATEM Setup Utility via USB. Please, follow the steps
then:
Step 1. Connect the switch chassis via USB, the computer running the configuration software Utilidadde dela ATEM.
Step 2. Start the configuration software Utilidadde dela ATEM.
Step 3. The switching current IP address and other settings and displayed in the window.
Step 4. To change the IP address or any other configuration, simply change the numbers and then click Apply.
Step 5. A dialog box will ask you to please, power cycle the switch ATEM.
ariel
hola Raguel
I have the ATEM 1 M / E Production the you mentioned, but I have a little problem with the network port that goes out from time to time and reconnects itself.. My query is as follows, something is wrong with the ATEM Broadcast or I have something that is not properly configured? I hope you can help me .. from now thank you very much..
Ragüel Burns
Hello. Sorry to hear of your problem. Need to know what happens when you turn off the network when “shuts” . DOES swicher you stop working? It could be a network configuration problem. The LAN has two swicher. In theory it would go perfect with both but the two test. But we would see the computer but while testing it and tell me.
regards
Jesus jaimes
I have control panel and I need to know how to put the cameras that I stay with the demarcation of the SDI follows 1.2.3.4.las first and 5.6.7.8. I use the HDMI or computer through behind it grabs control panel as I should
Ragüel Burns
First you must configure the Atem with the computer / computer. You'll have to give the same settings to all so make sure that all cameras without the same format. The camera 1 HDMI or Component is. The chambers 2,3 y 4 are HDMI and 5, 6, 7 y and are SDI. I hope you have been helpful. If you have any further questions do come to me and help you smoothly.
73tv
Hello Friend
can help us?
as we put the audio in the Atem? we have connected the cable but do not see any control panel. Well, if you look at the audio panel but do not see any active input.
Could you explain how to proceed?
Thanks
Ragüel Burns
The Atem 1 and 2 not yet have the ability to manage / configure the audio. They have mandártelo from a console or other device. If you connect via USB 3.0 if they have a small graphic meter. We have told the company this summer hope to activate the audio control options.
Kroezy
I read here that you have some experience with black magic I'm also long been a question that maybe you can answer.
I wish Blackmagic Design Intensity Shuttle Thunderbolt for me to buy DSRL to me macbook to kopelen. I work on mac and then wanted to go inporteren with black magic media express. I need about 45 minute film and the customer wants the following 10 mpeg2 or mpeg4 min have. Can this way of working through this? Oh the client runs on a windows.
Ragüel Burns
The Blackmagic capture allow the computer and the computer you export to the formats you want, including the ones you mentioned MPEG2 or MPEG4. With Final Cut X will go faster. This, too, is important. If you are into buying sure it is compatible with the video editor you want to use.